.png)
Click To Enlarge
PLEASE CALL FOR AVAILABILITY AND MORE DETAILS.
| Sensor Specifications & Compatibility | ||
| Catalog Number | E61800 | |
| Output Signal in Air | 10mV 15.5mV | |
| Response Time T 90% | < 15 seconds | |
| Nominal Sensor Lifetime | 900 000 % volume Oxygen hours | |
| Electrical Interface | Monojack | |
| Compatibility: | Maxtec MaxO2+AE, OM-25AE, OM-25ME | |
| MaxBlend, MaxVenturi MAX250E (MAX-250E) | ||
| CareFusion (Cardinal, Viasys) Sentry Blender | ||
| Newport Medical E360 & E500 ventilators | ||
| Teledyne R29MED , C-70592 | ||
| Viasys Sentry Blender, 66045 | ||
| 10-103-08 | ||
| Fluke VT Mobile | ||
| PSR-11-917-J1 | ||
| Notes: External Type sensor, see E61810 for Internal sensor. | ||
| Medical Oxygen Sensors (Fuel Cells) general specifications: | ||
| Measurement Range: | 0-100 % oxygen | |
| Accuracy and Repeatability: | < 1 % vol. O2when calibrated at 100 % O2 | |
| Zero Ofset: | < 0.5 % vol. O2in 100% N2, applied 5 minutes | |
| Linearity Error: | < 3 % relative | |
| Cross Interference: | < 0.5 % vol. O2response to: | |
| 10 % CO2balance N2 | ||
| 80% N2O balance N2 | ||
| 7.5% Halothane balance N2 | ||
| 7.5 % Isofurane balance N2 | ||
| 7.5 % Enfurane balance N2 | ||
| 9% Sevofurane balance N2 | ||
| 20% Desfurane balance N2 | ||
| Infuence of Humidity: | - 0.03 % rel. per % RH at 25ðC | |
| Infuence of Pressure: | proportional to change in oxygen partial | |
| pressure | ||
| Infuence of Mechanical Shock: | < 1% relative after a fall from 1m | |
| Operating Temperature: | 0 to 50ðC | |
| Temperature Compensation: | built-in NTC compensation (see below) | |
| Efect of Temperature | between +5 ðC and +25 ðC: 3 % relative error | |
| Compensation (steady state): | between 0 ðC and +50 ðC: 8 % relative error | |
| Operating Humidity: | 0-99 % RH non-condensing | |
| Long Term Output Drift: | < 1 % vol oxygen per month | |
| typically < - 15 % relative over lifetime | ||
| Storage Temperature: | -20 to +50 ðC | |
| Recommended Storage: | +5 to +15 ðC | |
| Recommended Load: | 10 kOhms | |
| Warm-Up Time: | < 30 minutes, after replacement of sensor | |
| Weight: | approximately 28 grams | |
| approximately 43 grams E61912 series | ||
| Designed and manufactured according to EN ISO 9001 : 2000 and EN13485 : 2003 | ||
| specifications are applicable at standard conditions: 1013 hPa, 25ðC dry ambient air |
||
O2 Sensor for Maxtec CAG250E, MAX-250E, Newport E360 and E500
- Item #: B226-211
- Manufacturer: WestPrime Healthcare
- Manufacturer's Product Number: E61800
- Condition: New
No Reviews. Write a Review
.jpg)
